1．规格  Specification
1.1 压缩机  Compressor

压缩机型号 Compressor Model	401DHV-64D2Y
压缩机型式 Compressor Type	变频压缩机 Inverter Controlled Compressor
压缩机方式 Compression Type	涡旋式 Scroll Type
使用冷媒 Refrigerant	R22
排气容积 Displacement	64cm3/rev
润滑油 / 油量 Oil / Oil Charge	SUNISO 4GDI-HT / 1800ml
涂装 Painting	黑色 Black Color Paint
总质量(含油) Net Mass(Including Oil)	37kg
吸气管接口内径 Suction Accept I.D	Ф22.2mm
排气管接口内径 Discharge Accept I.D	Ф12.9mm
CCC认证号 CCC Certification No.	2003010704098719

 
1.2 电机  Motor

变频器电源 Transducer Power		380/415V，3～，50Hz/60Hz
电动机型式 Motor Type		三相感应电机3 Phase Induction Motor
运转频率范围Running Frequency Range		30～90Hz
频率变化Frequency Vary	加速Acceleration Speed	1Hz/s～3Hz/s
	减速Decelerate Speed	0.5Hz/s
工作电压范围 Voltage Range		基本V/F特性±10%  Basic V/F±10%
绝缘等级 Insulation Class		F级  F Class
绕组阻抗 Winding Resistance(at 20℃)		0.8646±7%Ω
基本V/F特性 Basic V/F Characteristics

 
1.3 性能  Performance

制冷能力 Capacity	at 60Hz	14200W
输入功率 Motor Input		4300W
能效比 EER		3.30W/W
运行电流 Running Current		11.5A
噪音 Sound Level		≤60dB(A)
振动 Vibration		≤15 m/s2

 
※ 制冷能力测试条件 Test condition of cooling capacity：
冷凝温度 Condensing temp.：54.4 ℃           蒸发温度 Evaporating temp.：7.2 ℃
回气温度 Return gas temp.：18.3 ℃           周围温度 Ambient temp.：35.0 ℃
膨胀阀前液体温度 Liquid temp.：46.1℃
1.4 一般特性  Characteristics 

气密试验压力 Leak Tight Pressure	3.0MPa[高压侧 H.P. Side] / 1.5MPa[低压侧L.P. Side]
耐压试验压力Hydrostatic Strength Pressure	4.5MPa[高压侧 H.P. Side] / 2.3MPa[低压侧L.P. Side]
绝缘阻抗 Insulation Resistance	10MΩ Min.
绝缘耐压 Withstand Voltage	1,830V-1min.
残余水分量 Residual Moisture	350mg Max.
含尘量 Residual Impurities	100mg Max.

 
2. 压缩机配件  Accessories Of Compressor

NO.	名称 Parts Name	数量 Qty	代号 Drawing NO.	备注 Remarks
1	防振胶垫 Rubber Grommet B	4	TP1-102	标准部件 Standard Parts
2	防振胶座 Rubber Grommet A	4	TP1-103
3	温控器挡板 Thermostat Holder	1	TP1-105
4	排气温控器 Discharge Thermostat	1	TP1-106
5	弹性垫圈 Spring Washer	4	GB93-87-6
6	支撑螺柱 Bolt	4	TP1-101	选择部件 Option Parts
7	垫圈 Washer	4	TP1-104
8	M6螺母 M6 Screw Nut	4	GB41-86-M6
9	M8螺母 M8 Screw Nut	4	GB41-86-M8
10	热油器 Crankcase Heater	1	TP1-110

 
3. 使用条件范围  Operating Conditions

蒸发温度 Evaporating Temp.	-15～15℃
排气温度 Discharge Temp.	(冷凝温度＋15℃)～120℃以下 (Condensing Temp.＋15℃)～120℃ Max.
绕组温度 Winding Temp.	120℃以下 Max.
压缩机外壳温度 Shell Temp.	115℃以下 Max.
吸气压力 Suction Pressure	0.1～0.7MPa (起动、除霜等短时间运转除外；Except the short period such as start,defrost)
排气压力 Discharge Pressure	1.1～2.8MPa
压力比 Pressure Ratio	2～7.5 (起动、除霜等短时间运转除外；Except the short period such as start,defrost)
起动时的压力差 Pressure Difference At Starting	排气压力－吸气压力≤0.30MPa D.P.-S.P. less than 0.30MPa
启停周期 On/Off Period	周期为10分钟以上，停止时间必须3分钟以上 10 minutes min/cycle,OFF should be over 3 minutes
最低油量 Minimum Oil Charge	400ml Min.
异常升压/降压 Abnormal Press. Rise/Drop	上升:3.0MPa以下  Rise:3.0MPa Max.
	下降:0.2MPa以上  Drop:0.2MPa Min.
配管（铜管）应力 Copper Piping Stress	启动时:50MPa以下  Start:50MPa Max.
	运转时:10MPa以下  Run:10MPa Max.
冷媒水分含量 Refrigerant Moisture Level	60ppm以下 Max.
系统固体杂质含量 Solid Impurities Level	100mg以下 Max.
运转倾斜角度 Tilt In Operation	压缩机倾斜最大5°以内  5 deg. Max.

 
※ 其他注意事项  Remarks:

1. 制冷系统 The refrigeration system

1）润滑油与冷媒的重量比（润滑油/冷媒）应在0.4以上；
  The ratio of oil to the refrigerant (oil/refrigerant) should be higher than 0.4 in weight basis.
2）当系统中压缩机存在液态冷媒回流情况时，应采用储液罐等设计避免液态冷媒回流；
  When the compressor in the system has the liquid refrigerant flooding back operation,the accumulator is required.
3）向压缩机充油或冷媒时，必须从排气侧进行；
Charge oil or refrigerant from the discharge pipe.
4）系统应设置高压压力开关，参考设定值为2.8±0.1MPa。
Using high pressure switch in the refrigeration system is required,we advise setting pressure as follow: 2.8±0.1MPa,

2. 压缩机在去除吸、排气接头盖后，请勿放置10分钟以上；

Installation shall be completed within 10 minutes after removing the caps of suction and discharge tube.

3. 请勿压缩空气；

Do not compress air.

4. 在真空状态下请勿通电；

Do not energize under vacuumed condition.

5. 热泵系统必须在压缩机底部安装油加热器（40～80W,220V）；

Crankcase heater is required if the refrigeration system is heat pump.

6. 运转时，各相间的电压偏差应在额定电压的3％以内；

Voltage (run):Voltage deviation each phase shall be within 3% of the rated voltage.

7. 请勿反向旋转；

Do not reverse rotate.
8.压缩机的接地装置应永久与制冷器具的接地装置连接；
The compressor’s ground should be connected with that of refrigeration system permanently and firmly.
9.成箱压缩机包装件的叠放堆码极限为2箱,装卸过程中严禁翻滚。
Pile limits 2 pallet.Tumbling is forbidden during handling.
 
4. 附图  Attachment                          
A-1      压缩机外形图  Dimension of Compressor                                
A-2      防振胶座装配图  Mounting Assembly                                                   
A-3      压缩机性能曲线1  Compressor Performance Curve 1               
A-4      压缩机性能曲线2  Compressor Performance Curve 2
A-5      排气温控器组装图及零件图  Discharge Gas Thermostat Assembly Diagram
A-6      热油器安装图  Crankcase Heater Assembly 
福粤制冷想了解更多日立压缩机知识请点如下网站：日立压缩机，日立空调压缩机，日立变频压缩机，日立螺杆压缩机  http://www.hitachizg.com/    http://www.lengku1.com/